Step-by-step Tutorial: How to Tether Jailbreak and Unlock iPhone 4 Using Sn0wBreeze 2.9.7 (Windows) [iOS 6.0.1]
Using this tutorial you will be able to create a custom firmware, tether jailbreak and unlock iOS 6.0.1 running on iPhone 4. This tutorial uses Sn0wBreeze 2.9.7 for Windows.
Tethered jailbreak means that each time you restart your device you will need to connect it to a computer and run iBooty.
Sn0wBreeze 2.9.7 allows users to preserve modem version for unlock.
Important: There is no official Ultrasn0w that supports iOS 6.0.1. However there is an unofficial patch that will help. It works in most cases, but is recommended only for those who cannot downgrade to earlier iOS.
We are not developers of jailbreak utilities, so we cannot assure that everything will work just fine. However we tried this tutorial on several devices and succeeded.
Extract the Sn0wBreeze executable from zip archive.
Connect your iPhone 4 to the computer and launch iTunes.
Select your iPhone from the list of devices on the left.In iTunes 11 to activate left panel press Ctrl+S.
Create a backup by right-clicking on iPhone name in Devices (iTunes left pane) and choosing Back Up. In iTunes 11 you can click Back Up Now button.
Remember that Sn0wBreeze will preserve the baseband (modem) version. If you don't want to preserve (f.e. you don't need unlock), go ahead and update to iOS 6.0.1 in iTunes:
If you need unlock skip this and go to Step Two.
If you are already have iOS 6.0.1 installed go to Step Two.
Open iTunes. Now hold down Option (Mac)or Shift (Windows) key and click the Restore button.
Navigate to the Pwnage folder on your desktop and select the iOS 6.0.1 firmware ipsw. Click the Open button to continue.
After iOS update iTunes might ask if you want to setup your iPhone as a new device or restore from the backup. Ignore this or choose anything. It doesn't matter, since you will restore once again to a custom firmware.
Double click on Sn0wbreeze exe icon to launch the application.
The application will launch. Click Ok button.
You will see the main window. Press blue-arrow button.
You will see IPSW selection menu. Click Browse button.
Navigate to folder with downloaded firmware, select it and click Open button.
Sn0wBreeze will start identifying the firmware.
Sn0wbreeze will report the device information and firmware version. Check that this corresponds to your device. The screenshot below shows how this looks like for iPhone 4.
Press blue-arrow next button.
You will see the choice of 4 options.
Click on Expert Mode.
You will see the menu with General, Custom boot logos, Custom packages, Build IPSW. Some options might be disabled, if not supported with you device or firmware.
Click on General and then next blue arrow.
Here you can enable or disable several options.
Important: Choose Activate only if you need hactivation, if you do not plan to use your device with official carrier.
Click next blue arrow button.
You will see a windows where you can install custom packages, that will be embedded to your custom firmware.
Click next. You are ready to create custom IPSW. Click Build IPSW and next button.
Wait while IPSW is being built.You can play PamMan game while you're waiting.
Then you will see Done screen:
Press Ok button.
Now you have to follow instructions to put your device into DFU mode.
Please plug your iPhone into the computer and make sure its OFF then click the Start button.
1. Hold down both the Home button and the Power button for 10 seconds.
2. Release the Power button and continue holding the Home button until Sn0wbreeze detects the device.
If you fail to put the device into DFU mode you can start again.
If you have followed the steps correctly, you will get the following message from Snw0breeze:
Close all opened windows of Sn0wbreeze and launch iTunes.
Select your device from the list of devices on the left. Now hold down Shift and click the Restore button.
Navigate to the Desktop folder and select the newly created custom firmware ipsw. The name will be sn0wbreeze_iPhone_4-GSM-6.0.1-10A523.ipsw.. Click the Open button to continue.
iTunes will now restore the firmware on your iPhone. This can also take up to 10 minutes. Once done you will be rebooted into jailbroken iOS 6.0.1!
After the restore you're done! Your device is jailbroken.
iTunes will ask if you want to setup your iPhone as a new device or restore from the backup. Choose Restore from Backup if you want to preserve your contacts and other information.
Now you will need to boot tethered your iPhone 4. You will need to do it everytime you restart.
Sn0wBreeze created folder iBooty-for-6.0.1 on your desktop. Open it.
Choose your device in Select your iDevice option.
Push Start button.
Now you will need to put your device into DFU. Follow the instructions:
1. Prepare to press Home + Power
2. Press Home + Power buttons and hold them for 10 seconds.
3. Release Power, but keep holding Home button for 30 seconds.
You're done. Your iPhone successfully booted tethered.
Run Cydia. Let it do all the necessary updates.
To have access to the root file system of your iPhone (via file managers like iFunBox or iPhone Explorer) install application called afc2add in Cydia.
If you need carrier unlock – install ultrasn0w via Cydia (if you do not need carrier unlock skip this step).